Skip to main content
Install a Zebra Printer Shelf
Curtis Nash avatar
Written by Curtis Nash
Updated over a week ago

Install a Zebra Printer Shelf

Overview:

This guide will help you install a Zebra printer shelf. You can choose to mount it directly into a stud or use drywall anchors if you can’t find a stud. Follow these steps to ensure a secure installation.

Disclaimer & Warnings

▢ Jolt is not responsible or liable for any injuries or damage that may occur during install.

▢ Before installation ensure there are not any electrical, water, etc. lines or anything else that could be damaged in the wall.

▢ Be attentive of sharp corners and edges.

Materials Needed

  • Printer Shelf

  • Zebra Printer and Power Cord

  • Self-Tapping Screws (for Metal Studs)

  • Drywall Anchors

  • Stud Finder

  • Level

  • Electric Drill

  • Hammer

  • Pencil

Installation Steps

1. Stud Install (Mounting into a Stud)

  1. Find the Stud

    • Use the stud finder to locate and mark the center of the stud at your desired height.

  2. Align the Shelf

    • Position the printer shelf so that the mounting holes align with the center of the stud. Use a level to ensure the shelf is even.

  3. Mark the Holes

    • With a pencil, mark all four holes on the wall.

  4. Drill Pilot Holes

    • Use an electric drill with the appropriate size bit to drill two pilot holes into the stud.

  5. Drill Holes for Anchors

    • Drill two additional holes where the drywall anchors will be placed.

  6. Insert Anchors

    • Hammer the anchors into the non-stud holes, making sure they are flush with the wall.

  7. Attach the Shelf

    • Align the shelf with the holes and drive the screws into place using the drill.

  8. Install the Printer

    • Place the printer on the shelf and feed the power cord through the bottom hole.

  9. Add Extra Labels

    • Attach extra labels on the side of the shelf for convenience.

2. Anchor Install (Mounting without a Stud)

  1. Avoid Studs

    • Use the stud finder to ensure there are no studs in the area where you plan to mount the shelf.

  2. Align and Mark

    • Position the printer shelf with the level, then mark all four mounting holes on the wall.

  3. Drill Holes for Anchors

    • Drill four holes where the anchors will be placed.

  4. Insert Anchors

    • Hammer the anchors into the holes, ensuring they are flush with the wall.

  5. Attach the Shelf

    • Align the shelf with the holes and drive the screws into place using the drill.

  6. Install the Printer

    • Place the printer on the shelf and feed the power cord through the bottom hole.

  7. Add Extra Labels

    • Attach extra labels on the side of the shelf for convenience.

FAQs

Q: What should I do if I can’t find a stud?

A: Use drywall anchors to mount the shelf if you cannot locate a stud. Make sure to follow the instructions for using anchors to ensure a secure installation.

Q: How can I ensure the shelf is level?

A: Use a level when aligning the shelf to make sure it is even. Adjust as necessary before marking the holes.

Q: What if I accidentally drill into a stud?

A: If you accidentally drill into a stud, you can still use the holes for mounting. Just ensure that the screws are properly aligned and securely fastened.

Q: How do I know which drill bit to use?

A: Use a drill bit that matches the size of the screws or anchors you are using. Check the packaging for the recommended drill bit size.

Q: Can I install the shelf on a brick or concrete wall?

A: For brick or concrete walls, you will need different hardware such as masonry screws and wall plugs. Consult a hardware store or professional for the appropriate materials.

Q: What should I do if I encounter any issues during installation?

A: If you encounter issues, consult a professional or someone experienced in installing hardware to avoid damage or improper installation.

Q: How should I handle the power cord for the printer?

A: Feed the power cord through the bottom hole of the shelf to keep it organized and avoid tangles.

Did this answer your question?